Xerox workcentre 3045 ошибка 077 900

12.05.2014

Вопрос:

Подскажите что делать. Выпала ошибка на мфу workcentre 6015n   «077-900, замятие бумаги, откройте заднюю крышку». Бумагу убрал, но ошибка не пропадает, не знаю что делать уже все перепробовал. Помогите пожалуйста!!

Ответ:

077-900, 077-901. Застревание бумаги в зоне блока фьюзера или под левой крышкой. Вытащите застрявшую бумагу. Тщательно проверьте не осталось ли бумага в принтере, если вы все убрали, закройте крышку и перезапустите аппарат!

Задайте свой вопрос

077-101, 077-900 Registration Sensor Jam RAP

BSD-ON: BSD 8.5 Registration

077-101 The trail edge of the paper does not deactuate the registration sensor within the specified time after the registration clutch is energized.
077-900 The registration sensor detected remaining paper.

Initial Actions

• Check the condition of the paper in all trays. Refer to GP 15 Paper and Media Size Specifications.
• Ensure that all the trays are loaded correctly.

Procedure

WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.

Refer to the procedures that follow as necessary:

• GP 6 How to Check a Motor.
• GP 7 How to Check a Sensor.

Perform the steps that follow:

1. Check for obstructions in the paper path.
2. Check the registration roll and takeaway roll 1, PL 80.55 for foreign substances or wear. Clean or install new components as necessary.
3. Enter dC330, code 077-104. Check the registration sensor, PL 80.55 Item 4.
4. Enter dC330, code 042-003. Check the main motor, PL 40.10 Item 10.
5. Enter dC330, code 077-002. Check the registration clutch, PL 80.55 Item 11.
6. Check the drive assembly, PL 40.10 Item 1 for wear or damage.
7. Check the registration transport assembly, PL 80.55 Item 1 for wear or damage.
8. If the fault persists, install new components as necessary:

• Drive PWB, PL 1.10 Item 3.
• ESS PWB, PL 3.10 Item 6.

**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner’s property.**

You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.

Toner Chip (For North America and West Europe Region):

• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738

Toner Chip (For South America and East Europe Region):

• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766

Toner Chip (For Metered Machine):

• 106R03733 106R03736 106R03735 106R03734

Drum Chip:

• 113R00780 113R00782

077-900 Registration Sensor Static Jam RAP

BSD-ON:

BSD 8.5 — Registration

When the power was turned ON, the M/C was stopped (Cycle Down/ Shut Down), or when the

interlocks were closed (all interlocks including options), the Registration Sensor detected

paper.

NOTE: When turning the power OFF, turn OFF the power switch first and then the main power

switch.

Procedure

Check the following:

•

The Registration Sensor for remaining paper, contamination, Actuator return failure, or

improper installation

•

The Registration Sensor for failure:

Component Control

•

The connection between the Registration Sensor

open circuit, short circuit, and poor contact

Reload the machine software

(GP

16). If no problems are found, replace the MCU PWB

18.2).

Status Indicator RAPs

077-900, 077-901

[077-104]

(PL

15.1)

P/J121

and the MCU PWB

P/J415

for

(PL

07/2011

2-812

BUS Updated 12/2011

077-901 Exit Sensor 1 Static Jam RAP

BSD-ON:

BSD 10.2 — Fusing

When the power was turned ON, the M/C was stopped (Cycle Down/ Shut Down), or when the

interlocks were closed (all interlocks including options), the Fuser Exit Sensor detected paper.

NOTE: When turning the power OFF, turn OFF the power switch first and then the main power

switch.

Procedure

Check the following:

•

The Fuser Exit Sensor for remaining paper, contamination, Actuator return failure, or

improper installation

•

The Fuser Exit Sensor for failure:

Component Control

Reload the machine software

(GP

16). If no problems are found, replace the MCU PWB

18.2).

[077-101]

(PL

7.1)

Initial Issue

WorkCentre 5335 Family Service Documentation

(PL