Ошибка (Error) Service Call 231 (Вызов технической помощи 231) возникает на любых моделях цветных принтеров и МФУ OKI. Официально ошибка означает: Ошибка связи с устройством чтения RFID-чипа. Для этой ошибки существуют дополнительные коды, указанные после слова Error. Их значения приведены ниже:
Service call 231:Error 01 — ошибка связи между RFID-считывателем и платой принтера
Service call 231:Error 02 — ошибка платы трансивера в RFID-считывателе
Service call 231:Error 03 — ошибка связи между RFID-считывателем и тонер-картриджем
Service call 231:Error 04 — ошибка определения тонер-картриджа (более чем 4)
Service call 231:Error 05 — ошибка связи с чипом Black
Service call 231:Error 06 — ошибка связи с чипом Yellow
Service call 231:Error 07 — ошибка связи с чипом Magenta
Service call 231:Error 08 — ошибка связи с чипом Cyan
Service call 231:Error 11 — считыватель Black обнаружил чип другого цвета
Service call 231:Error 12 — считыватель Yellow обнаружил чип другого цвета
Service call 231:Error 13 — считыватель Magenta обнаружил чип другого цвета
Service call 231:Error 14 — считыватель Cyan обнаружил чип другого цвета
Service call 231:Error 21 — ошибка определения чипа ремня/печки
Service call 231:Error 22 — ошибка версии чипа ремня/печки
Service call 231:Error 23 — ошибка связи с чипом ремня/печки
Это всё официальные сведения.
А неофициально и в рамках Российской действительности — у вас в тонер-картридже левый чип! Совсем левый, то есть очень не качественный — именно он вызывает ошибку 231 с дополнительными кодами от 01 до 14. Понятно, что чип ставят для использования заправки. Если уж очень хочется заправлять — меняйте поставщика чипов! Ошибка эта, как и другие ошибки на OKI — не сбрасывается! После установки в тонер-картридж качественного чипа или, что лучше, после замены заправленного тонер-картриджа на оригинал ошибка Service Call 231 автоматически пропадёт.
Step 1 – Solve Oki Error Codes 231
Is Oki Error Codes 231 appearing? Would you like to safely and quickly eliminate service call 231 which additionally can lead to a blue screen of death?
When you manually edit your Windows Registry trying to take away the invalid oki printer error codes keys you’re taking a authentic chance. Unless you’ve got been adequately trained and experienced you’re in danger of disabling your computer system from working at all. You could bring about irreversible injury to your whole operating system. As very little as just 1 misplaced comma can preserve your Pc from even booting every one of the way by!
Troubleshooting oki c531dn error codes Windows XP, Vista, 7, 8 & 10
Simply because this chance is so higher, we hugely suggest that you make use of a trusted registry cleaner plan like CCleaner (Microsoft Gold Partner Licensed). This system will scan and then fix any Oki Error Codes 231 complications.
Registry cleaners automate the entire procedure of finding invalid registry entries and missing file references (including the Error error) likewise as any broken hyperlinks inside of your registry.
Issue with oki b4600 error codes
Backups are made immediately prior to each and every scan providing you with the choice of undoing any changes with just one click. This protects you against doable damaging your pc. Another advantage to these registry cleaners is that repaired registry errors will strengthen the speed and performance of one’s procedure drastically.
- http://www.chinadsong.com/article/Technology__Support/Analytical/20130906/394.html
- http://www.justanswer.com/printers/7jtx2-following-replacement-original-low-capacity-toner-cartridges.html
- http://www.printcopy.info/?l=en&mod=free&chap=erc&brand=OKI&model=C831n&code=231
- http://www.fixya.com/support/t1663181-oki_c5800ldn_231_fatal_error_03
Cautionary Note: Yet again, for those who are not an state-of-the-art consumer it’s very encouraged that you simply refrain from editing your Windows Registry manually. If you make even the smallest error within the Registry Editor it can result in you some serious issues that may even call for a brand new set up of Windows. Not all difficulties attributable to incorrect Registry Editor use are solvable.
Fixed: oki b710 error codes
Symptoms of Oki Error Codes 231
“Oki Error Codes 231” appears and crashes the energetic method window.
Your Personal computer routinely crashes with Oki Error Codes 231 when running the exact same system.
“Oki Error Codes 231” is shown.
Windows operates sluggishly and responds little by little to mouse or keyboard input.
Your computer periodically “freezes” for the number of seconds in a time.
Will cause of Oki Error Codes 231
Corrupt obtain or incomplete set up of Windows Operating System software program.
Corruption in Windows registry from a new Windows Operating System-related application adjust (install or uninstall).
Virus or malware infection which has corrupted Windows method documents or Windows Operating System-related application data files.
Another method maliciously or mistakenly deleted Windows Operating System-related files.
Mistakes this sort of as “Oki Error Codes 231” can be brought about by several different elements, so it really is important that you troubleshoot every of the achievable brings about to forestall it from recurring.
Simply click the beginning button.
Variety “command” inside the lookup box… Will not hit ENTER nonetheless!
Although keeping CTRL-Shift in your keyboard, hit ENTER.
You’re going to be prompted that has a authorization dialog box.
Click on Of course.
A black box will open having a blinking cursor.
Variety “regedit” and hit ENTER.
Within the Registry Editor, choose the oki printer error codes connected key (eg. Windows Operating System) you wish to back again up.
Within the File menu, choose Export.
Inside the Preserve In list, pick out the folder in which you wish to save the Windows Operating System backup key.
Inside the File Title box, sort a reputation for the backup file, these types of as “Windows Operating System Backup”.
From the Export Vary box, ensure that “Selected branch” is selected.
Click on Help you save.
The file is then saved by using a .reg file extension.
You now use a backup within your oki c531dn error codes related registry entry.
Solution to your oki b431dn error codes problem
There are actually some manual registry editing measures that can not be talked about in this article due to the high chance involved for your laptop or computer method. If you want to understand more then check out the links below.
Additional Measures:
One. Conduct a Thorough Malware Scan
There’s a probability the Error Oki Codes 231 error is relevant to some variety of walware infection. These infections are malicious and ready to corrupt or damage and possibly even delete your ActiveX Control Error files. Also, it’s attainable that your Oki Error Codes 231 is actually connected to some element of that malicious plan itself.
2. Clean oki c511 error codes Disk Cleanup
The a lot more you employ your computer the extra it accumulates junk files. This comes from surfing, downloading packages, and any sort of usual computer system use. When you don’t clean the junk out occasionally and keep your program clean, it could turn into clogged and respond slowly. That is when you can encounter an Codes error because of possible conflicts or from overloading your hard drive.
Once you clean up these types of files using Disk Cleanup it could not just remedy Oki Error Codes 231, but could also create a dramatic change in the computer’s efficiency.
Tip: While ‘Disk Cleanup’ is definitely an excellent built-in tool, it even now will not completely clean up Error Codes discovered on your PC. There are numerous programs like Chrome, Firefox, Microsoft Office and more, that cannot be cleaned with ‘Disk Cleanup’.
Since the Disk Cleanup on Windows has its shortcomings it is extremely encouraged that you use a specialized sort of challenging drive cleanup and privacy safety application like CCleaner. This system can clean up your full pc. If you run this plan after each day (it could be set up to run instantly) you are able to be assured that your Pc is generally clean, often operating speedy, and always absolutely free of any Oki error associated with your temporary files.
How Disk Cleanup can help oki c511dn service call 231 error 03
1. Click your ‘Start’ Button.
2. Style ‘Command’ into your search box. (no ‘enter’ yet)
3. When holding down in your ‘CTRL-SHIFT’ important go ahead and hit ‘Enter’.
4. You will see a ‘permission dialogue’ box.
5. Click ‘Yes’
6. You will see a black box open up plus a blinking cursor.
7. Variety in ‘cleanmgr’. Hit ‘Enter’.
8. Now Disk Cleanup will start calculating the amount of occupied disk space you will be able to reclaim.
9. Now a ‘Disk Cleanup dialogue box’ seems. There will be a series of checkboxes for you personally to pick. Generally it will likely be the ‘Temporary Files’ that consider up the vast majority of your disk area.
10. Verify the boxes that you want cleaned. Click ‘OK’.
How to repair service call 231 error 01 oki
3. System Restore can also be a worthwhile device if you ever get stuck and just desire to get back to a time when your computer system was working ideal. It will work without affecting your pics, paperwork, or other crucial information. You can discover this option with your User interface.
Error Codes
Manufacturer
Device
Operating System
Oki Error Codes 231
4 out of
5
based on
46 ratings.
leenoga
- Joined
- Dec 31, 2019
- Messages
- 6
-
#1
Okay I have figured out that this error code is related to the image drum assembly. And in particular related to the Cyan!!
The explanation I got was C reader (TC/ID — Tag Interface connection error! Well that does not tell me too much because I don’t even know what the word TAG stands for. There is a lack of communication evidently between something on the IMAGE DRUM ASSEMBLY and the Control Board or whatever. The problem is in the image drum assy because I have a spare drum assy from another printer and installed it and I do not get the error message.
Thus I looked over the drum assembly very carefully. I am trying to get this printer on line and have installed a whole new set of color cartridges so it shouldn’t be a toner cartridge problem but who knows?
Here is what I come up with of what I think the problem may be or close to it. On the left side of the assembly there are four sensors or indicators for each toner. They have a little window of sorts. Each one has two springs going into them. I have not had one off yet but looks like they are removable with one screw perhaps.
What are these for? What do they indicate or how do they work? Anyway the Cyan is the only window that is wide open and is perhaps why I am getting the error code 231 — 08.
I do not see any individual parts listed in the Oki Parts for the Image drum. Looks like if anything goes wrong they want you to purchase the whole enchilada image drum assy.
If any of you can help me out, I would sure appreciate it. Do you know of anyone that might have any used or spare parts for these printers if the company will not provide any?
leenoga
- Joined
- Dec 31, 2019
- Messages
- 6
-
#2
No responses. I am naturally disappointed. Thought someone would read my message and have some input.
Lee
-
#3
OKI MC363. Same error Code — 231 — 08. I came to the same conclusion. I replaced the drum, but the problem reappeared. The new drum comes with blank toner cartridges. Once you put the replacement toner cartridges in, the problem resurfaces. Perhaps, the problem is with the toner replacement cartridges. Price for Oki OEM toner cartridges are exhorbitant. Bought this printer just 1 or so years ago. What a shame.
Anyone have any solutions?
Last edited: Jan 25, 2022
– Compatible Printer model: OKI C831n
– OKI C831n Error Code description:
- Code: 001
- Display: Service call 001: Error
- Description: Machine Check Exception hardware fault detection (board failure or poor power supply)
- Troubleshooting Guides: Replace the CU/ PU board.
- Code: 002 … 007
- Display: Power Off/On 002: Error to 007: Error PC: nnnnnnnn LR: nnnnnnnn FR: nnnnnnnn
- Description: CPU unexpected exception
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Replace the CU/ PU board.
- Code: 009
- Display: Power Off/On 009: Error PC: nnnnnnnn LR: nnnnnnnn FR: nnnnnnnn
- Description: CPU unexpected exception
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Replace the CU/ PU board.
- Code: 010
- Display: Power Off/On 010: Error PC: nnnnnnnn LR: nnnnnnnn FR: nnnnnnnn
- Description: CPU unexpected exception
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Replace the CU/ PU board.
- Code: 011
- Display: Power Off/On 011: Error PC: nnnnnnnn LR: nnnnnnnn FR: nnnnnnnn
- Description: CPU unexpected exception
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Replace the CU/ PU board.
- Code: 020
- Display: Service call 020: Error
- Description: CU Program ROM Hash Check Error
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Replace the CU/ PU board.
- Code: 023
- Display: Service call 023: Error
- Description: CU Font ROM Hash error
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Replace the CU/ PU board.
- Code: 030
- Display: Service call 030: Error
- Description: CU RAM Check Error
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Replace the CU/ PU board.
- Code: 031
- Display: Service call 031: Error
- Description: CU Optional RAM Check Error
- Troubleshooting Guides: Is implementation of the RAM DIMM normal? Does replacement of the program RAM DIMM restore the printer?
Re-implement the RAM DIMM. Replace the RAM DIMM. Replace the CU/ PU board.
- Code: 036
- Display: Service call 036: Error
- Description: CU RAM DIMM spec. is not supported.
- Troubleshooting Guides: Is the RAM DIMM genuine? Is implementation of the RAM DIMM normal? Does replacement of the program RAM DIMM restore the printer?
Use a genuine RAM DIMM. Re-implement the RAM DIMM. Replace the RAM DIMM. Replace the CU/PU board (EEPROM replacement required).
- Code: 040
- Display: Service call 040: Error
- Description: CU EEPROM Error
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Replace the CU/ PU board.
- Code: 042, 043, 045
- Display: Service call 042: Error~ 043: Error 045: Error
- Description: Flash File System Error
Failed to access to the Flash ROM that is directly mounted on the CU board. - Troubleshooting Guides: Failed to access to the Flash ROM that is directly mounted on the CU board. Format the Flash forcibly. (This requires caution as it erases NIC-F/W. The NIC-F/W must be written with the maintenance utility after formatting.) Execute system maintenance menu > MAINTENANCE MENU > FLASH FORMAT. After FLASH FORMAT is displayed, release the button and wait until the ON LINE is displayed (about 2 minutes). If the error remains, replace the CU/PU board.
Solve OKI C831n Error codes
- Code: 049
- Display: Service call 049: Error
- Description: Incompatibility between the CU and the engine head type (resolution)
- Troubleshooting Guides: 1) Replace the CU/ PU board with the one for the proper head. 2) Replace with a head of proper resolution.
- Code: 052
- Display: Power off/on 052: Error
- Description: A DMA Abort error was detected with the Image Processor.
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Replace the CU/ PU board.
- Code: 067
- Display: Service call 067: Error
- Description: A communication error was detected during communication with the Sleep Mode interface supervisor program.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 068
- Display: Service call 068: Error
- Description: The Sleep Mode interface supervisor program was not found.
- Troubleshooting Guides: Does this error recur after power restoration? Yes Program writing by service personnel.
- Code: 069
- Display: Service call 069: Error
- Description: Malfunction of the NIC chip was detected.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 070
- Display: Power off/on 070: Error
- Description: A PSE firmware error was detected.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 072
- Display: Power off/on 072: Error.
- Description: Engine I/F Error. I/F error between PU and CU
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 073
- Display: Power off/on 073: Error
- Description: An error was detected during image data expansion.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 075
- Display: Power off/on 075: Error
- Description: An error was detected during image data expansion.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 077
- Display: Power off/on 077: Error
- Description: An error was detected during image data expansion.
- Troubleshooting Guides: Does this error recur? Yes Replace the CU/ PU board
- Code: 081
- Display: Service call 081: Error
- Description: Normal reading/ writing of EEPROM or Flash has become impossible.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 104
- Display: Service call 104: Error
- Description: The engine EEPROM implementation check at power on showed no problem, but after that a read/write error was detected.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 106
- Display: Service call 106: Error
- Description: Abnormal engine control logic
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 111
- Display: Service call 111: Error
- Description: A duplex unit for another model was detected.
- Troubleshooting Guides: Is a duplex unit provided for this model installed? No Install a correct duplex unit.
- Code: 112
- Display: Service call 112: Error
- Description: A 2nd Tray for another model was detected.
- Troubleshooting Guides: Is a 2nd Tray provided for this model installed? No Install a correct 2nd Tray.
- Code: 113
- Display: Service call 113: Error
- Description: A 3rd Tray for another model was detected.
- Troubleshooting Guides: Is a 3rd Tray provided for this model installed? No Install a correct 3rd Tray.
- Code: 114
- Display: Service call 114: Error
- Description: A 4th Tray for another model was detected.
- Troubleshooting Guides: Is a 4th Tray provided for this model installed? No Install a correct 4th Tray.
- Code: 121
- Display: Service call 121: Error
- Description: High voltage power supply interface error
- Troubleshooting Guides: Is the cable connecting the CU board to the high voltage power supply unit connected properly? Is there any defective contact point?
Re-connect them properly. Check for defective contact points of the high voltage system. Replace the high voltage power supply unit.
- Code: 122
- Display: Service call 122: Error
- Description: Low voltage FAN error
- Troubleshooting Guides: Is the FAN (bottom right of the front) of the low voltage power supply block working? Is the FAN connector connected correctly?
Check to make sure connection of the FAN connector. Replace the low voltage power supply unit. Replace the FAN motor. Replace the low voltage power supply unit.
- Code: 123
- Display: Service call 123: Error
- Description: Abnormal environment humidity or unconnected humidity sensor
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the control panel board (PCQ board).
- Code: 124
- Display: Service call 124: Error
- Description: Abnormal environment humidity
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the control panel board (PCQ board).
- Code: 126
- Display: Power off/on 126: Error
- Description: Dew condensation in the printer was detected.
- Troubleshooting Guides: This error tends to occur after a printer is carried in from the outsides. Leave the printer for 2 hours to half a day at room temperature, and turn on the power. Does this error recur?
After leaving the printer at room temperature, turn on the power again. Replace the control panel board (PCQ board).
- Code: 127
- Display: Service call 127: Error
- Description: Fuser FAN error
- Troubleshooting Guides: Is the FAN connector connected properly? Does this error recur?
Re-connect it properly. Replace the FAN motor. Replace the CU/ PU board.
- Code: 128
- Display: Service call 128: Error
- Description: Fan motor abnormality 04: Belt FAN 05: Fuser side FAN 08: ID motor FAN
- Troubleshooting Guides: Is the cable to respective fans connected properly? Does this error recur? Does this error recur?
Connect the FAN connector properly. Replace the FAN. Replace the CU/ PU board.
- Code: 131 … 134
- Display: Service call 131: Error to 134: Error
- Description: LED head detection error (131=Y, 132=M, 133=C, 134=K)
- Troubleshooting Guides: Is the LED head connected properly? Is the LED HEAD fuse brown? Does this error recur?
Install the LED head unit properly. Check the LED HEAD fuse. Replace the fuse. Restore the power. Replace the LED head unit.
- Code: 142
- Display: Service call 142: Error
- Description: Image drum Up/Down position detection error
- Troubleshooting Guides: Is the image drum unit caught by anything when it is removed or re-installed? Does this error recur at power on? Is the cable connected properly?
Re-install the image drum unit. Check connection through the CU/PU board, the relay connector, and the ID up/down clutch. Connect it properly. Replace the CU/ PU board.
- Code: 154
- Display: Service call 154: Error
- Description: The belt unit fuse blown out.
- Troubleshooting Guides: Is the belt unit connected properly? Does this error recur?
Re-install the belt unit. Restore the power. After checking for cable connection, replace the CU/PU board.
- Code: 155
- Display: Service call 155: Error
- Description: The fuser unit fuse blown out.
- Troubleshooting Guides: Is the fuser unit installed properly? Does this error recur?
After cleaning the connector of the fuser unit, re-install the fuser unit. Restore the power. After checking for cable connection, replace the CU/PU board.
- Code: 160 … 163
- Display: Service call 160: Error to 163: Error
- Description: Toner sensor detection error (160=Y, 161=M, 162=C, 163=K) This error does not occur with the factory default settings.
- Troubleshooting Guides: Is the toner cartridge installed? Is the lock lever of the toner set? Does this error recur?
Install the toner cartridge. Move the lock lever of toner cartridge to the lock position. Replace the toner sensor assembly.
- Code: 166
- Display: Service call 166: Error
- Description: An abnormality was detected with the power supply temperature thermistor.
01: Short 02: Open 03: High temp. 04: Low temp. - Troubleshooting Guides: 01, 02: Does this error recur? Does this error recur? Does this error recur? Restore the power. Replace the low voltage power supply unit. Replace the CU/ PU board. Replace the cable between the low voltage power supply unit and the CU/PU board.
03: Does this error recur? Remove anything obstructing the ventilation slots if any and restore the power. Replace the low voltage power supply unit. Replace the CU/ PU board. Replace the cable between the low voltage power supply unit and the CU/PU board.
04: Does this error recur? Raise the room temperature and restore the power. Replace the low voltage power supply unit. Replace the CU/ PU board. Replace the cable between the low voltage power supply unit and the CU/PU board.
- Code: 167
- Display: Service call 167: Error
- Description: Temperature difference error with Upper Center Thermistor and Planar Heater Thermistor
- Troubleshooting Guides: Is the error message displayed? Does this error recur?
Restore the power. Replace the fuser unit.
- Code: 168
- Display: Service call 168: Error
- Description: Planar Heater Thermistor Error
01: Short 02: Open 03: High temp. 04: Low temp. - Troubleshooting Guides: Is the error message displayed? Does this error recur?
Restore the power. Replace the fuser unit.
- Code: 169
- Display: Service call 169: Error
- Description: Upper Side thermistor error
01: Short 02: Open 03: High temp. 04: Low temp. - Troubleshooting Guides: Is the error message displayed? Does this error recur?
Restore the power. Replace the fuser unit.
- Code: 170, 171
- Display: Service call 170: Error, 171: Error
- Description: Short circuit or open circuit of the Upper Center Thermistor was detected.
- Troubleshooting Guides:
Does this error recur? Yes Restore the power. Replace the fuser unit.
- Code: 172, 173
- Display: Service call 172: Error, 173: Error
- Description: An either temperature aberration (a hightemperature or cold temperature) of Upper Center Thermistor, Lower Thermistor, Upper Side Thermistor, Planar Heater Thermistor was detected.
- Troubleshooting Guides: Does this error recur? Yes Restore the power. Replace the fuser unit.
- Code: 174, 175
- Display: Service call 174: Error, 175: Error
- Description: Short circuit or open circuit of the Lower Thermistor was detected.
- Troubleshooting Guides: Does this error recur? Yes Restore the power. Replace the fuser unit.
- Code: 176, 177
- Display: Service call 176: Error, 177: Error
- Description: An abnormal (high or low) temperature of the Lower Thermistor was detected.
- Troubleshooting Guides: Does this error recur? Yes Restore the power. Replace the fuser unit.
- Code: 181 … 184
- Display: Service call 181: Error to 184: Error
- Description: Option unit I/F error (181=Duplex Unit, 182 to 184=Optional Tray)
- Troubleshooting Guides: Does this error recur? Yes Restore the power. Check to make sure the contact points of the connector and replace the optional unit.
- Code: 190
- Display: Power off/on 190: Error
- Description: System memory overflow
- Troubleshooting Guides: Does this error recur? Yes Restore the power. Install an add-on RAM DIMM.
- Code: 200 … 202
- Display: Service call 200: Error to 202: Error
- Description: PU Firmware Download error
- Troubleshooting Guides: An error occurred during rewriting of the PU firmware. Restore the power and retry download. (This error doesn’t occur because this process is not performed in normal operation.)
- Code: 203, 204
- Display: Power off/on 203: Error, 204: Error
- Description: CU program error (not occur in normal operation)
The CU program executed abnormal processing. - Troubleshooting Guides: The CU program executed abnormal processing. Restore the power.
- Code: 207, 208
- Display: Power off/on 207: Error, 208: Error
- Description: CU program error (not occur in normal operation)
The CU program executed abnormal processing. - Troubleshooting Guides: The CU program executed abnormal processing. Restore the power.
- Code: 209
- Display: Power off/on 209: Download Error
- Description: Custom Media Type table downloading failed.
Custom Media Type table downloading failed. - Troubleshooting Guides: Custom Media Type table downloading failed. After turning on the power again, perform downloading again. (This error does not occur during the normal operation because this processing is not carried out in normal operation.)
- Code: 213, 214
- Display: Power off/on 213: Error, 214: Error
- Description: CU program error (not occur in normal operation)
The CU program executed abnormal processing. - Troubleshooting Guides: The CU program executed abnormal processing. Restore the power.
- Code: 230
- Display: Service call 230: Error
- Description: RFID Reader not Installed
- Troubleshooting Guides: RFID read device error Does this error recur? Yes Yes Check the FFC connecting the RFID R/W board and the CU/PU board. Replace the CU/ PU board and the RFID R/W unit (top cover).
- Code: 231
- Display: Service call 231: Error
- Description: 01: RFID Reader I/F Error
05: K reader (TC/ID) – Tag interface connection error
06: Y reader (TC/ID) – Tag interface connection error
07: M reader (TC/ID) – Tag interface connection error
08: C reader (TC/ID) – Tag Interface connection error
11: K reader (TC/ID) – Tag interface connection error
12: Y reader (TC/ID) – Tag interface connection error
13: M reader (TC/ID) – Tag interface connection error
14: C reader (TC/ID) – Tag interface connection error - Troubleshooting Guides: 01: Is the FFC connected properly? Does this error recur? Does this error recur?
Check the FFC connecting the RFID R/W board and the CU/PU board. Connect the FFC properly. Replace the CU/ PU board. Replace the RFID R/W unit (top cover).
05 to 08, 11 to 14: Does this error recur after the power restoration? Does this error recur after the power restoration? Is the antenna cable connected properly? Is the antenna set in the holder correctly? Does this error recur after the power restoration?
Move electronic equipment away from the printer is any on the printer, and restore the power. Replace the toner cartridge or ID of the indicated color. Check the antenna cable of the indicated color. Connect the cable properly. Adjust the antenna to the correct position. Replace the RFID R/W unit (top cover).
- Code: 232
- Display: Service call 232: Error
- Description: More than one image drum tag of the same color was detected.
- Troubleshooting Guides: Is more than one image drum installed? Yes Cycle the power. Replace the image drum in question.
- Code: 250
- Display: Power off/on 250: Error
- Description: An encrypted file erasing error was detected.
- Troubleshooting Guides: Did the user accept to execute Erase SD Card? Inform the user that it is necessary to execute Disk ERASE to restore the SD card defaults in order to delete the encrypted file.
- Code: 251
- Display: Service call 251: Error
- Description: An error was detected during SD Card Erase.
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Replace the SD card.
- Code: 254
- Display: Service call 254: Error
- Description: An unexpected error occurred during initialization in the Security mode.
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Regenerate an encryption key. If it doesn’t solve the problem, replace the CU/PU board or encrypted SD card.
- Code: 257
- Display: Service call 257: Error
- Description: An unexpected error occurred during initialization of the SD card.
- Troubleshooting Guides: Does this error message reappear? Yes Cycle the power. Format the SD card again. If it does not solve the problem, replace the SD card.
- Code: 901, 902
- Display: Power off/on 901: Error, 902: Error
- Description: Short circuit or open circuit with the bent thermistor was detected.
- Troubleshooting Guides: Is the belt thermistor cable connected properly? Does this error recur after power restoration?
Re-connect the cable properly. Replace the belt thermistor.
- Code: 903, 904
- Display: Power off/on 903: Error, 904: Error
- Description: The belt thermistor detected abnormal (too high or too low) temperature.
- Troubleshooting Guides: Is the belt thermistor cable connected properly? Does this error recur?
Re-connect the cable properly and restore the power. Replace the belt thermistor, after a lapse of 30 minutes, turn on the power.
- Code: 918
- Display: Power off/on 918: Error
- Description: Duplex FAN error
- Troubleshooting Guides: Does this error recur after power restoration? Does this error recur after power restoration? Does this error recur after power restoration?
Check if the duplex unit is installed properly. Check if the FAN is connected properly. Replace the FAN.
- Code: 923
- Display: Power off/on 923: Error
- Description: The ID motor is not running normally.
- Troubleshooting Guides: Does this error message reappear after power restoration? Does this error message reappear after power restoration?
Check if the image drum is installed properly. Replace the image drum unit. Replace the ID motor.
- Code: 928
- Display: Power off/on 928: Error
- Description: The fuser motor is not running normally.
- Troubleshooting Guides: Does this error message reappear after power restoration? Does this error message reappear after power restoration?
Check if the fuser is installed properly. Replace the fuser. Replace the fuser motor.
- Code: 931
- Display: Power off/on 931: Error
- Description: Duplex unit CPU clock frequency error
- Troubleshooting Guides: Does this error message reappear after power restoration? Does this error message reappear after power restoration?
Replace the unit. Replace the CU/ PU board.
- Code: 933
- Display: Power off/on 933: Error
- Description: Tray 2 CPU clock frequency error
- Troubleshooting Guides: Does this error message reappear after power restoration? Does this error message reappear after power restoration?
Replace the unit. Replace the CU/ PU board.
- Code: 934
- Display: Power off/on 934: Error
- Description: Tray 3 CPU clock frequency error
- Troubleshooting Guides: Does this error message reappear after power restoration? Does this error message reappear after power restoration?
Replace the unit. Replace the CU/ PU board.
- Code: 935
- Display: Power off/on 935: Error
- Description: Tray 4 CPU clock frequency error
- Troubleshooting Guides: Does this error message reappear after power restoration? Does this error message reappear after power restoration?
Replace the unit. Replace the CU/ PU board.
- Code: 941
- Display: Power off/on 941: Error
- Description: A watch dog timer error was detected.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 942
- Display: Power off/on 942: Error
- Description: An undefined interruption was detected.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 943
- Display: Power off/on 943: Error
- Description: PU CPU ran away out of control due to noise etc.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 944
- Display: Power off/on 944: Error
- Description: Dcon circuit access failed.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 945
- Display: Power off/on 945: Error
- Description: SDRAM access at power on failed.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 980
- Display: Power off/on 980: Error
- Description: An abnormal temperature of the fuser unit was detected.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the fuser unit.
- Code: 982
- Display: Service call 982: Error
- Description: Excessive trays beyond the specification are installed.
- Troubleshooting Guides: Are many trays beyond the specification installed? Yes Use trays as many as specified.
- Code: 983
- Display: Service call 983: Error
- Description: More than one toner cartridge tag of the same color was detected.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the CU/ PU board.
- Code: 984
- Display: Service call 984: Error.
- Description: A format tag not matching with the K position was detected.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the K toner cartridge or image drum.
- Code: 985
- Display: Service call 985: Error
- Description: A format tag not matching with the Y position was detected.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the Y toner cartridge or image drum.
- Code: 986
- Display: Service call 986: Error
- Description: A format tag not matching with the M position was detected.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the M toner cartridge or image drum.
- Code: 987
- Display: Service call 987: Error
- Description: A format tag not matching with the Cposition was detected.
- Troubleshooting Guides: Does this error recur? Yes Cycle the power. Replace the C toner cartridge or image drum.
- Code: 999
- Display: Service call 999: Error
- Description: The CU/PU firmware has a problem with its compatibility
- Troubleshooting Guides: Does an error occur at cycling the power? Yes Replace the CU/PU board or start printer by forced ONLINE (see Chapter 6) and rewrite the firmware.
- Code: F0C, FOD
- Display: Power off/on F0C, F0D: Error PC:nnnnnnnn LR:nnnnnnnn FR:nnnnnnnn
- Description: CU program error
- Troubleshooting Guides: Does this error recur? Yes Restore the power. Replace the CU/ PU board.
- Code: FFE
- Display: Power off/on FFE: Error PC:nnnnnnnn LR:nnnnnnnn FR:nnnnnnnn
- Description: CU program error
- Troubleshooting Guides: Does this error recur? Yes Restore the power. Replace the CU/ PU board.
- Code: FFF
- Display: Power off/on FFF: Error PC:nnnnnnnn LR:nnnnnnnn FR:nnnnnnnn
- Description: CU program error
- Troubleshooting Guides: Does this error recur? Yes Restore the power. Replace the CU/ PU board.
– Get more information about Epson XP 15000 troubleshooting, click here
– Get more error code list with quick guide to fix printer product, click here
– About get help with reseting Epson inkpad or others, click here
Waste Ink Pad Counter Utility Functions:
– Cleaning printhead.
– Ink charge.
– Fix Epson red lights blinking Error
– Fix Epson Service Required Error: A printer’s ink pad at the end of its service life Please contact Epson Support.
– Check the current value of waste ink counters and ink level counters.
– Clear Waste Ink Counters.
– Read and write serial number.
– Read and write USB ID.
– Read and write HEAD ID.
– Make EEPROM dump, backup.
– Paper feed test.
– Nozzle check.
– Color check pattern.
– Initialize (disable) PF deterioration offset.
– Retrieve device information
Contact us to get support with OKI C831n Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.